Difference between revisions of "SpaceElevatorRibbon"

From SpaceElevatorWiki.com
Jump to navigationJump to search
Line 56: Line 56:
|-
|-
|Production of carbon nantubes || Develop techniques for mass production of CNT based materials ||  
|Production of carbon nantubes || Develop techniques for mass production of CNT based materials ||  
*[[TBD| Ribbon refinement by User 1]]
|-
|Develop woven interconnects || As an alternative to tape sandwiches interconnects that are essentially CNT fibers woven around and through the axial fibers might perform better and be more resistant to the environment.  The ribbon would look like a woven cloth where the interconnects are and bare axial fibers between.  One issue is whether splicing can be done in the same way or if this can only be done with ribbon made on the ground. ||
*[[TBD| Ribbon refinement by User 1]]
*[[TBD| Ribbon refinement by User 1]]
|-
|-

Revision as of 04:39, 22 July 2008

The Ribbon

The core of the Space Elevator is the physical connection between Earth and space. In our baseline design this connection is in the form of a ribbon though earlier designs discussed a round cable.

The primary technical challenge to building the Space elevator has always been the availability of material with sufficient strength. The availability and strength of this material drives all aspects of the space elevator.


Basic Aspect Details
Material Carbon nanotube SWNT or MWNT two centimeters in length. General status of material see TetherDataTable.jpg also see the general file archive for this Wiki, numerous papers on CNT developments are located there
Width variable 10 cm wide in the lower atmosphere, widens to a meter at LEO and maintains this width for remainder of ribbon
Thickness Ill-defined Not a single mass, composed of axial fibers, area density in arbitrary units is 1 at LEO, 2.3 at GEO, and 10 at Earth due to width and tension requirements
Length 100,000 kilometers The length was selected based on engineering parameters such as relative mass of climber (counterweight) and cable and on the destinations of interest (Mars, asteroids).
Small scale design Spun CNT thread The number and diameter of the axial threads are yet to be determined and will be set by production limitations and ribbon robustness
Interconnects Tape sandwich Millimeter to several millimeter wide strips of gold-coated polymide tape with CNT reinforcing fibers roughly 10 microns thick. Spacing varies with the closest interconnects (10 cm) at and below LEO. Interconnects must be able to hold axial threads at 1% to 3% of their tension if broken allowing slippage at higher tension.


Ribbon closeup.jpg Ribbon 3d image.jpg

These images show the proposed basic design though not completely to scale. Many small axial, load-bearing fibers are held in a ribbon configuration by orthogonal epoxy, adhesive tape or woven interconnects. increasing the size of the ribbon is accomplished by splicing additional ribbons to the sides or face of the initial ribbon.

Discussions on the ribbon can be found File:Cable write up.odt and the basic spreadsheet for cable calculations for different planets, lift capabilities, lengths, etc. can be found in this File:Cable worksheet.ods

Insert Sketchup graphic and related Sketchup file http://sketchup.google.com/3dwarehouse/details?mid=bd063afd8c6594bb86852bf1a7913ebc&prevstart=0

Major Development Issues Related to this Component

  1. Stored Energy Release in Ribbon
  2. Splicing Ribbons During Construction
  3. Optimizing Ribbon Design
  4. Atomic Oxygen Effects on Ribbon
  5. Spooling of the Ribbon for Deployment
  6. Degradation of the Ribbon in the Space Environment
  7. Attaching the Ribbon to the Anchor


Additional Work Needed

The ribbon is the greatest technical challenge facing the space elevator. It must be extremely strong, fault-free and damage-tolerant, lightweight, and resistant to radiation, ultraviolet and atomic oxygen.

Item Notes Completed and Ongoing Efforts
Production of carbon nantubes Develop techniques for mass production of CNT based materials
Develop woven interconnects As an alternative to tape sandwiches interconnects that are essentially CNT fibers woven around and through the axial fibers might perform better and be more resistant to the environment. The ribbon would look like a woven cloth where the interconnects are and bare axial fibers between. One issue is whether splicing can be done in the same way or if this can only be done with ribbon made on the ground.
Develop ribbon designs and optimize components Optimize thread size for production and use, develop and test optimal interconnects (woven, tape sandwiches, epoxy,...)
Make and test various ribbon designs Aligned threads with orthogonal interconnects, cross-linked tethers (Hoytether), solid sheets... test for fault tolerance, strength to weight ratio,
Test CNT threads to destruction Test the energy storage and dissipation when a CNT thread is pulled to breaking


Return to Overview